Textination Newsline

Reset
8 results
Bacteria, eating Plastic and producing Multipurpose Spider Silk Photo: Kareni, Pixabay
05.02.2024

Bacteria, eating Plastic and producing Multipurpose Spider Silk

For the first time, researchers have used bacteria to “upcycle” waste polyethylene: Move over Spider-Man: Researchers at Rensselaer Polytechnic Institute have developed a strain of bacteria that can turn plastic waste into a biodegradable spider silk with multiple uses.

Their new study marks the first time scientists have used bacteria to transform polyethylene plastic — the kind used in many single-use items — into a high-value protein product.

That product, which the researchers call “bio-inspired spider silk” because of its similarity to the silk spiders use to spin their webs, has applications in textiles, cosmetics, and even medicine.

For the first time, researchers have used bacteria to “upcycle” waste polyethylene: Move over Spider-Man: Researchers at Rensselaer Polytechnic Institute have developed a strain of bacteria that can turn plastic waste into a biodegradable spider silk with multiple uses.

Their new study marks the first time scientists have used bacteria to transform polyethylene plastic — the kind used in many single-use items — into a high-value protein product.

That product, which the researchers call “bio-inspired spider silk” because of its similarity to the silk spiders use to spin their webs, has applications in textiles, cosmetics, and even medicine.

“Spider silk is nature’s Kevlar,” said Helen Zha, Ph.D., an assistant professor of chemical and biological engineering and one of the RPI researchers leading the project. “It can be nearly as strong as steel under tension. However, it’s six times less dense than steel, so it’s very lightweight. As a bioplastic, it’s stretchy, tough, nontoxic, and biodegradable.”

All those attributes make it a great material for a future where renewable resources and avoidance of persistent plastic pollution are the norm, Zha said.

Polyethylene plastic, found in products such as plastic bags, water bottles, and food packaging, is the biggest contributor to plastic pollution globally and can take upward of 1,000 years to degrade naturally. Only a small portion of polyethylene plastic is recycled, so the bacteria used in the study could help “upcycle” some of the remaining waste.

Pseudomonas aeruginosa, the bacteria used in the study, can naturally consume polyethylene as a food source. The RPI team tackled the challenge of engineering this bacteria to convert the carbon atoms of polyethylene into a genetically encoded silk protein. Surprisingly, they found that their newly developed bacteria could make the silk protein at a yield rivaling some bacteria strains that are more conventionally used in biomanufacturing.

The underlying biological process behind this innovation is something people have employed for millennia.

“Essentially, the bacteria are fermenting the plastic. Fermentation is used to make and preserve all sorts of foods, like cheese, bread, and wine, and in biochemical industries it’s used to make antibiotics, amino acids, and organic acids,” said Mattheos Koffas, Ph.D., Dorothy and Fred Chau ʼ71 Career Development Constellation Professor in Biocatalysis and Metabolic Engineering, and the other researcher leading the project, and who, along with Zha, is a member of the Center for Biotechnology and Interdisciplinary Studies at Rensselaer.

To get bacteria to ferment polyethylene, the plastic is first “predigested,” Zha said. Just like humans need to cut and chew our food into smaller pieces before our bodies can use it, the bacteria has difficulty eating the long molecule chains, or polymers, that comprise polyethylene.

In the study, Zha and Koffas collaborated with researchers at Argonne National Laboratory, who depolymerized the plastic by heating it under pressure, producing a soft, waxy substance. Next, the team put a layer of the plastic-derived wax on the bottoms of flasks, which served as the nutrient source for the bacteria culture. This contrasts with typical fermentation, which uses sugars as the nutrient source.

“It’s as if, instead of feeding the bacteria cake, we’re feeding it the candles on the cake,” Zha said.

Then, as a warming plate gently swirled the flasks’ contents, the bacteria went to work. After 72 hours, the scientists strained out the bacteria from the liquid culture, purified the silk protein, and freeze dried it. At that stage, the protein, which resembled torn up cotton balls, could potentially be spun into thread or made into other useful forms.

“What’s really exciting about this process is that, unlike the way plastics are produced today, our process is low energy and doesn’t require the use of toxic chemicals,” Zha said. “The best chemists in the world could not convert polyethylene into spider silk, but these bacteria can. We’re really harnessing what nature has developed to do manufacturing for us.”

However, before upcycled spider silk products become a reality, the researchers will first need to find ways to make the silk protein more efficiently.

“This study establishes that we can use these bacteria to convert plastic to spider silk. Our future work will investigate whether tweaking the bacteria or other aspects of the process will allow us to scale up production,” Koffas said.

“Professors Zha and Koffas represent the new generation of chemical and biological engineers merging biological engineering with materials science to manufacture ecofriendly products. Their work is a novel approach to protecting the environment and reducing our reliance on nonrenewable resources,” said Shekhar Garde, Ph.D., dean of RPI’s School of Engineering.

The study, which was conducted by first author Alexander Connor, who earned his doctorate from RPI in 2023, and co-authors Jessica Lamb and Massimiliano Delferro with Argonne National Laboratory, is published in the journal “Microbial Cell Factories.”

Source:

Samantha Murray, Rensselaer

Chemist Unlocks Plastic Alternatives Using Proteins and Clothing Scraps Photo: Challa Kumar, professor emeritus of chemistry, in his lab. (Contributed photo)
21.12.2023

Chemist Unlocks Plastic Alternatives Using Proteins and Clothing Scraps

Challa Kumar has developed methods to create novel plastic-like materials using proteins and fabric.

Every year, 400 million tons of plastic waste are generated worldwide. Between 19 and 23 million tons of that plastic waste makes its way into aquatic ecosystems, and the remaining goes into the ground. An additional 92 million tons of cloth waste is generated annually.

Challa Kumar, professor emeritus of chemistry, “fed up” with the tremendous amount of toxic waste people continually pump into the environment, felt compelled to do something. As a chemist, doing something meant using his expertise to develop new, sustainable materials.

“Everyone should think about replacing fossil fuel-based materials with natural materials anywhere they can to help our civilization to survive,” Kumar says. “The house is on fire, we can’t wait. If the house is on fire and you start digging a well – that is not going to work. It’s time to start pouring water on the house.”

Challa Kumar has developed methods to create novel plastic-like materials using proteins and fabric.

Every year, 400 million tons of plastic waste are generated worldwide. Between 19 and 23 million tons of that plastic waste makes its way into aquatic ecosystems, and the remaining goes into the ground. An additional 92 million tons of cloth waste is generated annually.

Challa Kumar, professor emeritus of chemistry, “fed up” with the tremendous amount of toxic waste people continually pump into the environment, felt compelled to do something. As a chemist, doing something meant using his expertise to develop new, sustainable materials.

“Everyone should think about replacing fossil fuel-based materials with natural materials anywhere they can to help our civilization to survive,” Kumar says. “The house is on fire, we can’t wait. If the house is on fire and you start digging a well – that is not going to work. It’s time to start pouring water on the house.”

Kumar has developed two technologies that use proteins and cloth, respectively, to create new materials. UConn’s Technology Commercialization Services (TCS) has filed provisional patents for both technologies.

Inspired by nature’s ability to construct a diverse array of functional materials, Kumar and his team developed a method to produce continuously tunable non-toxic materials.

“Chemistry is the only thing standing in our way,” Kumar says. “If we understand protein chemistry, we can make protein materials as strong as a diamond or as soft as a feather.”

The first innovation is a process to transform naturally occurring proteins into plastic-like materials. Kumar’s student, Ankarao Kalluri ’23 Ph.D., worked on this project.

Proteins have “reactor groups” on their surfaces which can react with substances with which they come into contact. Using his knowledge of how these groups work, Kumar and his team used a chemical link to bind protein molecules together.

This process creates a dimer – a molecule composed to two proteins. From there, the dimer is joined with another dimer to create tetramer, and so on until it becomes a large 3D molecule. This 3D aspect of the technology is unique, since most synthetic polymers are linear chains.

This novel 3D structure allows the new polymer to behave like a plastic. Just like the proteins of which it is made, the material can stretch, change shape, and fold. Thus, the material can be tailored via chemistry for a variety of specific applications.

Unlike synthetic polymers, because Kumar’s material is made of proteins and a bio-linking chemical, it can biodegrade, just like plant and animal proteins do naturally.

“Nature degrades proteins by ripping apart the amide bonds that are in them,” Kumar says. “It has enzymes to handle that sort of chemistry. We have the same amide linkages in our materials. So, the same enzymes that work in biology should also work on this material and biodegrade it naturally.”

In the lab, the team found that the material degrades within a few days in acidic solution. Now, they are investigating what happens if they bury this material in the ground, which is the fate of many post-consumer plastics.

They have demonstrated that the protein-based material can form a variety of plastic-like products, including coffee cup lids and thin transparent films. It could also be used to make fire-resistant roof tiles, or higher-end materials like, car doors, rocket cone tips, or heart valves.

The next steps for this technology are to continue testing their mechanical properties, like strength or flexibility, as well as toxicity.

“I think we need to have social consciousness that we cannot put out materials into the environment that are toxic,” Kumar says. “We just cannot. We have to stop doing that. And we cannot use materials derived from fossil fuels either.”

Kumar’s second technology uses a similar principle, but instead of just proteins, uses proteins reinforced with natural fibers, specifically cotton.

“We are creating a lot of textile waste each year due to the fast-changing fashion industry” Kumar says. “So why not use that waste to create useful materials – convert waste to wealth.”

Just like the plastic-like protein materials (called “Proteios,” derived from original Greek words), Kumar expects composite materials made from proteins and natural fibers will biodegrade without producing toxic waste.

In the lab, Kumar’s former student, doctoral candidate Adekeye Damilola, created many objects with protein-fabric composites, which include small shoes, desks, flowers, and chairs. This material contains textile fibers which serve as the linking agent with the proteins, rather than the cross-linking chemical Kumar uses for the protein-based plastics.

The crosslinking provides the novel material with the strength to withstand the weight that would be put on something like a chair or a table. The natural affinity between fibers and proteins is why it’s so hard to get food stains out of clothing. This same attraction makes strong protein-fabric materials.

While Kumar’s team has only worked with cotton so far, they expect other fiber materials, like hemp fibers or jute, would behave similarly due to their inherent but common chemical properties with cotton.

“The protein naturally adheres to the surface of the protein,” Kumar says. “We used that understanding to say ‘Hey, if it binds so tightly to cotton, why don’t we make a material out of it.’ And it works, it works amazingly.”

With the support of TCS, Professor Kumar is currently seeking industry partners to bring these technologies to market. For more information contact Michael Invernale at michael.invernale@uconn.edu.

Source:

Anna Zarra Aldrich '20 (CLAS), Office of the Vice President for Research

Photo: pixabay
24.08.2021

Air, Water, Oil: What PLA bioplastic can filter well - and what not

Air filters have been discussed so often in recent days in the fight against the pandemic. With filter material made of nonwoven fabric, they block the way back into rooms for aerosols containing viruses. But how can these devices not only protect health, but also be operated with filter material that is as environmentally friendly as possible?

Air filters have been discussed so often in recent days in the fight against the pandemic. With filter material made of nonwoven fabric, they block the way back into rooms for aerosols containing viruses. But how can these devices not only protect health, but also be operated with filter material that is as environmentally friendly as possible?

Under clearly defined conditions, the bioplastic polylactide (PLA), also known as polylactic acid, is suited for this purpose. This can be deduced from results obtained by researchers from the Zuse community in the recently completed "BioFilter" research project. The key question for this and other potential applications of biofilters is: How do the special properties of PLA affect the filter performance and durability? After all, PLA can have practical disadvantages compared to its fossil-based competitors. Its material tends to be brittle and it doesn't particularly like high temperatures beyond 60 degrees Celsius. As a biogenic material, polylactic acid is also potentially more susceptible to abrasion and organic degradation processes. This can play an even greater role in the use of filters, e.g. in sewage treatment facilities, than in air filters. Industrial customers, however, naturally want a durable, reliable product.

From monofilament to nonwoven
Against this background, the researchers studied the PLA properties in order to test nonwovens for biofilters on this basis. The German Textile Research Center North-West (German Textile Research Center North-West - DTNW) and the Saxon Textile Research Institute (STFI), where the nonwovens were produced, were involved. Granules from various commercially available manufacturers were used. However, the research did not start with nonwovens, in which the fibers are deposited close together in different layers, but with so-called monofilaments, i.e. fibers made of PLA that are comparable to threads. DTNW and STFI initially carried out tests on these monofilaments, e.g. in a climate chamber for aging and durability.

As can be seen in the picture, the monofilaments became brittle after only two weeks at higher temperatures from 70 degrees Celsius, as the DTNW authors recently reported in the Journal Applied Polymer Materials. Under normalized conditions, however, the monofilaments showed no measurable reduction in stability even after almost three years, and the PLA nonwovens were in no way inferior to their fossil-based counterparts in terms of filter performance. "In my opinion, the focus for the use of PLA as a filter material will be on applications where relatively low temperatures are present, with which PLA copes very well," says DTNW scientist Christina Schippers.

Besides temperature and humidity consider other factors
For the researchers, however, the project, which was funded by the German Federal Ministry for Economic Affairs and Energy, was not just about the suitability of polylactide for air filters, but also for other applications, such as filtering water. In addition, the research revealed that when evaluating filter media made from bio-based and biodegradable nonwovens, it is important to consider other influencing factors, such as mechanical loads caused by air currents, in addition to temperature and humidity. "The innovative core of the project was to evaluate the possibilities and application limits of PLA nonwovens as filter media with sufficient mechanical properties and long-term stability," says project leader Dr. Larisa Tsarkova. Like her colleagues at STFI, DTNW is involved in the Zuse Community's Bioeconomy Cluster, in which researchers from nonprofit institutes cooperate under the guiding principle of "Researching with Nature." "For us, the bioeconomy is a top cross-industry topic that connects numerous institutes of the Zuse Community and is lived through collaborations such as with the 'Bio-Filter'," explains the future STFI managing director Dr. Heike Illing-Günther.

Cooperation in the Bioeconomy Cluster
With the results obtained from the "Bio-Filter" project, DTNW and STFI now want to continue working in order to be able to make derivations for clearly described areas of application for PLA nonwoven filters in the future. These possible fields of application extend far beyond room air filters and thus beyond the pandemic. For example, the water-repellent property of PLA is potentially interesting for filters in large-scale kitchens for water-oil filtration or also in the industry for engine oils.

The research is also so important, because PLA is already quite well established in individual consumer-related segments - keyword: carrier bags. Traditionally, lactic acid was used to preserve food, for example in sauerkraut. Today, PLA is obtained via a multi-stage synthesis from sugar, which ferments to lactic acid and polymerizes this to PLA, as Kunststoffe.de explains. PLA is one of the best-known bioplastics, but has not always been readily available due to strong demand in recent years. The Netherlands-based company Total Corbion has announced plans to start up a PLA plant with an annual capacity of 100,000 tons in Grandpuits, France, by 2024. It would be the largest plant of its kind in Europe, with Asia leading the way so far.

Source:

Deutsche Industrieforschungsgemeinschaft Konrad Zuse e.V.

Photo: Pixabay
03.08.2021

Composites Germany presents results of the 17th Composites Market Survey

  • Highly positive rating of current business situation
  • Future expectations are optimistic
  • Varied expectations for application industries
  • Still the same growth drivers

This is the seventeenth time that Composites Germany has identified the latest KPIs for the fibre-reinforced plastics market. The survey covered all the member companies of the three major umbrella organisations of Composites Germany: AVK (Industrievereinigung Verstärkte Kunststoffe e.V.), Leichtbau Baden-Württemberg and the VDMA Working Group on Hybrid Lightweight Construction Technologies.

As before, to ensure a smooth comparison with the previous surveys, the questions in this half-yearly survey have been left unchanged. Once again, the data obtained in the survey is largely qualitative and relates to current and future market developments.

  • Highly positive rating of current business situation
  • Future expectations are optimistic
  • Varied expectations for application industries
  • Still the same growth drivers

This is the seventeenth time that Composites Germany has identified the latest KPIs for the fibre-reinforced plastics market. The survey covered all the member companies of the three major umbrella organisations of Composites Germany: AVK (Industrievereinigung Verstärkte Kunststoffe e.V.), Leichtbau Baden-Württemberg and the VDMA Working Group on Hybrid Lightweight Construction Technologies.

As before, to ensure a smooth comparison with the previous surveys, the questions in this half-yearly survey have been left unchanged. Once again, the data obtained in the survey is largely qualitative and relates to current and future market developments.

Highly positive rating of current business situation
After ratings of the current business situation had been steadily declining for nearly two years in succession, last year’s survey already displayed a trend reversal towards a more positive outlook. This positive trend has now continued in the latest survey, with entirely positive ratings for all three regions (Germany, Europe and worldwide). For ex-ample, 80% described the current general business situation as either positive or indeed very positive.

Moreover, unlike in the last survey, this more optimistic assessment applies not only to the general business situation, but also to the respondents’ own businesses, as they gave even more positive ratings than last year.     

There are currently quite a few challenges in the industrial environment. In many cases, the Covid-19 pandemic, for example, has merely receded, but has not disappeared.      
Business models have been and are still requiring adjustments. In some cases, supply chains have been severely disrupted and there are still some serious bottlenecks. The blockage of the Suez Canal by the Ever Given has once again highlighted the vulnerability of international commerce.

Shortages of raw materials, sharp increases in the prices of many raw materials and, most recently, a shortage of chips are having a major impact on various application industries. Nevertheless, the overall picture in the composites in-dustry is extremely optimistic. Similarly positive ratings were last achieved in the autumn 2018 and spring 2019 surveys.

Future expectations are optimistic
The positive prevailing mood is further reinforced by positive expectations for the future. A consistently optimistic picture emerged when respondents were asked about their ex-pectations for future business developments. For example, more than 80% of respond-ents are expecting the business situation in Europe to improve over the next six months. The pattern is similar for the other regions.

Varied expectations for application industries
Expectations on selected application industries vary substantially. As in the previous survey, significant declines are expected, above all, in automotive, aviation and wind energy. However, we can see that the proportion of respondents giving more pessimistic assessments has once again declined significantly.
Whereas, in the last sur-vey, 46% were expecting to see the situation get worse in aviation, this value has now dropped to a “mere” 17%. In the automotive sector, it has dropped from 17% (second half of 2020) to only 14%.

Two areas of application, in particular – infrastructure/construction and sports/leisure – have long been seen by many respondents as major growth stimulants for the composites industry. Even in times of a more difficult industrial environment, these two areas are currently proving to be especially robust.

GRP is still a growth driver
As before, the current market survey shows Germany, Europe and Asia as the global regions expected to deliver the most important growth stimuli for the composites segment. Expectations for Asia, on the other hand, have declined somewhat in favour of Europe. Where materials are concerned, we are seeing a continuation of the ongoing paradigm shift.      

Respondents are still convinced that CRP (carbon fibre reinforced plastic) is losing ground as a growth driver. However, GRP (glass fibre reinforced plastic) is now ranking as the most important material for the third time in succession. A large number of respondents have also mentioned the area entitled “Across All Segments” this time.

Composites are still relatively young materials with a great deal of potential. It remains exciting to see to what extent composites will continue to emerge as alternative materials and whether they can benefit from the major forthcoming developments (e.g. alternative drives, a growing demand for sustainability, alternative power sources, 5G, etc.).
The next Composites Market Survey will be published in January 2022. 

Photo: pixabay
20.07.2021

Closed-Loop Recycling Pilot Project for Single Use Face Masks

  • Circular economy for plastics: Fraunhofer, SABIC, and Procter & Gamble join forces

The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics. The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

The transformation from a linear to a circular plastics economy can only succeed with a multi-stakeholder approach. The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE combines the competencies of six institutes of the Fraunhofer-Gesellschaft and cooperates closely with partners from industry. Together, we work on systemic, technical and social innovations and keep an eye on the entire life cycle of plastic products.  

  • Circular economy for plastics: Fraunhofer, SABIC, and Procter & Gamble join forces

The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE and its Institute for Environmental, Safety and Energy Technology UMSICHT have developed an advanced recycling process for used plastics. The pilot project with SABIC and Procter & Gamble serves to demonstrate the feasibility of closed-loop recycling for single-use facemasks.

The transformation from a linear to a circular plastics economy can only succeed with a multi-stakeholder approach. The Fraunhofer Cluster of Excellence Circular Plastics Economy CCPE combines the competencies of six institutes of the Fraunhofer-Gesellschaft and cooperates closely with partners from industry. Together, we work on systemic, technical and social innovations and keep an eye on the entire life cycle of plastic products.  

Fraunhofer Institute for Environmental, Safety and Energy Technology UMSICHT is a pioneer in sustainable energy and raw materials management by supplying and transferring scientific results into companies, society and politics. Together with partners, the dedicated UMSICHT team researches and develops sustainable products, processes and services which inspire.

Fraunhofer Institute UMSICHT, SABIC and Procter & Gamble (P&G) are collaborating in an innovative circular economy pilot project which aimed to demonstrate the feasibility of closed-loop recycling of single-use facemasks.

Due to COVID-19, use of billions of disposable facemasks is raising environmental concerns especially when they are thoughtlessly discarded in public spaces, including - parks, open-air venues and beaches. Apart from the challenge of dealing with such huge volumes of essential personal healthcare items in a sustainable way, simply throwing the used masks away for disposal on landfill sites or in incineration plants represents a loss of valuable feedstock for new material.

“Recognizing the challenge, we set out to explore how used facemasks could potentially be returned into the value chain of new facemask production,” says Dr. Peter Dziezok, Director R&D Open Innovation at P&G. “But creating a true circular solution from both a sustainable and an economically feasible perspective takes partners. Therefore, we teamed up with Fraunhofer CCPE and Fraunhofer UMSICHT’s expert scientists and SABIC’s T&I specialists to investigate potential solutions.”

As part of the pilot, P&G collected used facemasks worn by employees or given to visitors at its manufacturing and research sites in Germany. Although those masks are always disposed of responsibly, there was no ideal route in place to recycle them efficiently. To help demonstrate a potential step change in this scenario, special collection bins were set up, and the collected used masks were sent to Fraunhofer for further processing in a dedicated research pyrolysis plant.

“A single-use medical product such as a face mask has high hygiene requirements, both in terms of disposal and production. Mechanical recycling, would have not done the job” explains Dr. Alexander Hofmann, Head of Department Recycling Management at Fraunhofer UMSICHT. “In our solution, therefore, the masks were first automatically shredded and then thermochemically converted to pyrolysis oil.

Pyrolysis breaks the plastic down into molecular fragments under pressure and heat, which will also destroy any residual pollutants or pathogens, such as the Coronavirus. In this way it is possible to produce feedstock for new plastics in virgin quality that can also meet the requirements for medical products” adds Hofmann, who is also Head of Research Department “Advanced Recycling” at Fraunhofer CCPE.

The pyrolysis oil was then sent to SABIC to be used as feedstock for the production of new PP resin. The resins were produced using the widely recognized principle of mass balance to combine the alternative feedstock with fossil-based feedstock in the production process. Mass balance is considered a crucial bridge between today’s linear economy and the more sustainable circular economy of the future.

“The high-quality circular PP polymer obtained in this pilot clearly demonstrates that closed-loop recycling is achievable through active collaboration of players from across the value chain,” emphasizes Mark Vester, Global Circular Economy Leader at SABIC. “The circular material is part of our TRUCIRCLE™ portfolio, aimed at preventing valuable used plastic from becoming waste and at mitigating the depletion of fossil resources.”

Finally, to close the loop, the PP polymer was supplied to P&G, where it was processed into non-woven fibers material. “This pilot project has helped us to assess if the close loop approach could work for hygienic and medical grade plastics.” says Hansjörg Reick, P&G Senior Director Open Innovation. “Of course, further work is needed but the results so far have been very encouraging”.

The entire closed loop pilot project from facemask collection to production was developed and implemented within only seven months. The transferability of advanced recycling to other feedstocks and chemical products is being further researched at Fraunhofer CCPE.

Photo: pixabay
06.07.2021

»Waste4Future«: Today's Waste becomes Tomorrow's Resource

Fraunhofer Institutes pave new ways in plastics recycling

A sustainable society, the renunciation of fossil raw materials, climate-neutral processes - also the chemical industry has committed itself to these goals. For the industry, this means a huge challenge within the next years and decades. This structural change can succeed if all activities - from the raw material base to material flows and process technology to the end of a product's life cycle - are geared towards the goal of sustainable value creation. The key to this is innovation.

Fraunhofer Institutes pave new ways in plastics recycling

A sustainable society, the renunciation of fossil raw materials, climate-neutral processes - also the chemical industry has committed itself to these goals. For the industry, this means a huge challenge within the next years and decades. This structural change can succeed if all activities - from the raw material base to material flows and process technology to the end of a product's life cycle - are geared towards the goal of sustainable value creation. The key to this is innovation.

Plastics such as polyethylene (PE), polypropylene (PP) or polystyrene (PS), which are currently produced almost entirely from fossil raw materials, are fundamental to many everyday products and modern technologies. The carbon contained in plastics is an important resource for the chemical industry. If it is possible to better identify such carbon-containing components in waste, to recycle them more effectively, and to use them again to produce high-quality raw materials for industry, the carbon can be kept in the cycle. This not only reduces the need for fossil resources, but also pollution with CO2 emissions and plastic waste. At the same time, the security of supply for industry is improved because an additional source of carbon is tapped.

The "Waste4Future" lighthouse project therefore aims to create new opportunities for recycling plastics in order to make the carbon they contain available as a "green" resource for the chemical industry. "We are thus paving the way for a carbon circular economy in which valuable new base molecules are obtained from plastic waste and emissions are largely avoided: Today's waste becomes tomorrow's resource," says Dr.-Ing. Sylvia Schattauer, deputy director of the Fraunhofer Institute for Microstructure of Materials and Systems IMWS, which is heading the project. "With the know-how of the participating institutes, we want to show how the comprehensive recycling of waste containing plastics without loss of carbon is possible and ultimately economical through interlocking, networked processes." The outcome of the project, which will run until the end of 2023, is expected to be innovative recycling technologies for complex waste that can be used to obtain high-quality recyclates.

Specifically, the development of a holistic, entropy-based assessment model is planned (entropy = measure of the disorder of a system), which will reorganize the recycling chain from process-guided to material-guided. A new type of sorting identifies which materials and in particular which plastic fractions are contained in the waste. Based on this analysis, the total stream is separated and a targeted decision is then made for the resulting sub-streams as to which recycling route is the most technically, ecologically and economically sensible for this specific waste quantity. What cannot be further utilized by means of mechanical recycling is available for chemical recycling, always with the aim of preserving the maximum possible amount of carbon compounds. Burning waste containing plastics at the end of the chain is thus eliminated.

The challenges for research and development are considerable. These include the complex evaluation of both input materials and recyclates according to ecological, economic and technical criteria. Mechanical recycling must be optimized, and processes and technologies must be established for the key points in the material utilization of plastic fractions. In addition, suitable sensor technology must be developed that can reliably identify materials in the sorting system. Machine learning methods will also be used, and the aim is to link them to a digital twin that represents the properties of the processed materials.

Another goal of the project is the automated optimization of the formulation development of recyclates from different material streams. Last but not least, an economic evaluation of the new recycling process chain will be carried out, for example with regard to the effects of rising prices for CO2 certificates or new regulatory requirements. The project consortium will also conduct comprehensive life cycle analysis (LCA) studies for the individual recycling technologies to identify potential environmental risks and opportunities.

For the development of the corresponding solutions, the participating institutes are in close exchange with companies from the chemical industry and plastics processing, waste management, recycling plant construction and recycling plant operation, in order to consider the needs of industry in a targeted manner and thus increase the chances of rapid application of the results achieved.

The following Institutes are involved in the Fraunhofer lighthouse project "Waste4Future":

  • Fraunhofer Institute for Microstructure of Materials and Systems IMWS (lead)
  • Fraunhofer Institute for Non-Destructive Testing IZFP
  • Fraunhofer Institute for Materials Recycling and Resource Strategy IWKS
  • Fraunhofer Institute of Optronics, System Technologies and Image Exploitation IOSB
  • Fraunhofer Institute for High Frequency Physics and Radar Techniques FHR
  • Fraunhofer Institute for Structural Durability and System Reliability LBF
  • Fraunhofer Institute for Process Engineering and Packaging IVV
(c) Fraunhofer IAP
08.06.2021

Fraunhofer IAP: Recyclable, Fiber-reinforced Material made from Bio-based Polylactic Acid

"Packaging made from bio-based plastics has long been established. We are now supporting the further development of these materials for new areas of application. If in the future the market also offers plant-based materials for technically demanding tasks such as vehicle construction, the bioeconomy will take a decisive step forward," explained Uwe Feiler, Parliamentary State Secretary at the Federal Ministry of Food and Agriculture, in Potsdam. The occasion was the handover of a grant to the Fraunhofer Institute for Applied Polymer Research IAP. The Fraunhofer IAP wants to develop a composite material that consists entirely of bio-based polylactic acid (PLA) and is significantly easier to recycle than conventional fiber composites.

"Packaging made from bio-based plastics has long been established. We are now supporting the further development of these materials for new areas of application. If in the future the market also offers plant-based materials for technically demanding tasks such as vehicle construction, the bioeconomy will take a decisive step forward," explained Uwe Feiler, Parliamentary State Secretary at the Federal Ministry of Food and Agriculture, in Potsdam. The occasion was the handover of a grant to the Fraunhofer Institute for Applied Polymer Research IAP. The Fraunhofer IAP wants to develop a composite material that consists entirely of bio-based polylactic acid (PLA) and is significantly easier to recycle than conventional fiber composites.

The German Federal Ministry of Food and Agriculture (BMEL) is intensively promoting the development of biomaterials as part of its Renewable Resources funding program. More than 100 projects are currently underway, covering a wide range of topics: from plastics that are degradable in the sea to natural fiber-reinforced lightweight components for the automotive sector. The projects are supported by the Agency for Renewable Resources, the BMEL project management agency responsible for the Renewable Resources funding program.

Easier recycling of fiber-reinforced plastics
PLA is one of the particularly promising bio-based materials. The global market for this polymer is growing by around 10 percent a year. PLA is also used, among other things, as a matrix in fiber-reinforced plastics. In these mechanically resilient plastics, reinforcing fibers are embedded in a plastic matrix.

The Fraunhofer IAP project is now focusing on these reinforcing fibers: "We are further developing our PLA fibers in order to transfer them to industrial scale together with partners from industry. These fibers are ideally suited for reinforcing PLA plastics. The resulting self-reinforcing single-component composite promises great recycling benefits. Since the fiber and the matrix of PLA are chemically identical, complex separation steps are not necessary," explains Dr. André Lehmann, expert for fiber technology at Fraunhofer IAP.

Novel PLA fibers and films are more thermally stable
The challenge with this approach is that conventional PLA has a relatively low temperature resistance. Technical fibers can be produced most economically using the melt spinning process. The Fraunhofer IAP team is now using more thermally stable stereocomplex PLA (sc-PLA) for the fibers. The term stereocomplex refers to a special crystal structure that the PLA molecules can form. Sc-PLA fibers have a melting point that is 40 - 50 °C higher and can therefore withstand the incorporation process in a matrix made of conventional PLA. In the project, the researchers are developing and optimizing a melt spinning process for sc-PLA filament yarns. The partner in this work package is Trevira GmbH, a manufacturer of technical and textile fiber and filament yarn specialties that are in demand from automotive suppliers and contract furnishers, among others. Furthermore, the development of a manufacturing process for sc-PLA reinforced flat films is planned. The international adhesive tape manufacturer tesa SE is participating in this task, and will test the suitability of sc-PLA films as adhesive foils. In a third work package, the Fraunhofer IAP will finally process the filaments in a double pultrusion process to produce granules suitable for injection molding.

Bio-based solutions for the automotive and textile industries
The scientists led by Dr. André Lehmann are certain that the self-reinforced PLA material can conquer many new areas of application. The automotive and textile industries are already showing interest in bio-based materials that are also easier to recycle. In terms of price, PLA would already be competitive here, and now the material is also to be made technically fit for the new tasks.

Professor Alexander Böker, head of Fraunhofer IAP, says: "The steadily growing demand from industry for sustainable solutions underlines how important it is to develop biobased and at the same time high-performance materials. With our research, we are also actively driving the development of a sustainable and functioning circular economy and therefore very much welcome the support from the federal government."

Information on the project is available at fnr.de under the funding code 2220NR297X.

Composites Europe 2019 (c) Photos: Reed Exhibitions/ Oliver Wachenfeld
30.07.2019

COMPOSITES EUROPE 2019: Digital Process Chain makes Fibre Composites Competitive

  • Strong Triple: COMPOSITES EUROPE, International Composites Conference and Lightweight Technologies Forum
  • “Process live” special areas showcase technological progress
  • Co-located event: Foam Expo Europe

The composites industry provides important impetus – for lightweight construction and material innovations in automotive, aviation, mechanical engineering, construction, wind power as well as in the sports and leisure sectors. So in international competition it is solutions with a high degree of automation that are in demand. COMPOSITES EUROPE from 10 to 12 September will present the trends and advances in the production and processing of fibre-reinforced plastics in Stuttgart. The trade fair will be accompanied by the International Composites Conference and the Lightweight Technologies Forum. Also held in parallel at the Messe Stuttgart premises will be Foam Expo Europe.

  • Strong Triple: COMPOSITES EUROPE, International Composites Conference and Lightweight Technologies Forum
  • “Process live” special areas showcase technological progress
  • Co-located event: Foam Expo Europe

The composites industry provides important impetus – for lightweight construction and material innovations in automotive, aviation, mechanical engineering, construction, wind power as well as in the sports and leisure sectors. So in international competition it is solutions with a high degree of automation that are in demand. COMPOSITES EUROPE from 10 to 12 September will present the trends and advances in the production and processing of fibre-reinforced plastics in Stuttgart. The trade fair will be accompanied by the International Composites Conference and the Lightweight Technologies Forum. Also held in parallel at the Messe Stuttgart premises will be Foam Expo Europe.

Trade fair visitors will meet with over 300 exhibitors from 30 nations who will be displaying materials, technical solutions and innovative application examples in Stuttgart. Apart from novel products the trade fair will place special emphasis on innovative process engineering. Visitors will learn about the state of play in serial production and new applications in the composites industry in the exhibition area as well as on numerous special areas, on themed guided tours, at the accompanying International Composites Conference and at the Lightweight Technologies Forum, which is dedicated to the trends in multi-material lightweight construction.

“Process live”: Technologies in Synergy
Perfectly coordinated processing and manufacturing processes will be centre stage at the “Process live” event. On shared exhibition space machinery and equipment manufacturers will exhibit their technologies in concert and – what’s more – in operation so as to show the different individual processes in a real context.  

On display, to name but one exhibit, is VAP®, the Vacuum Assisted Process patented by Airbus, which will be in the limelight in the Trans-Textil and Composyst special area. This process permits the one-step production of large-surface and geometrically complex components without an autoclave, which is why it is particularly suitable for structural components in aviation, wind power, shipbuilding, in rail and road transport, in machinery and device manufacturing as well as in architecture and in the leisure industry.

The “Process live” special area care of cutting specialists GUNNAR from Switzerland specifically targets the DACH region (Germany, Austria, Switzerland) with its small and medium-sized companies. Jointly with laser projection expert LAP and composites engineering expert SCHEURER Swiss, GUNNAR introduces a connected overall process that fuses modern machinery and software with specialists’ manual jobs. The point of departure here is an automated manufacturing process for sorted layer placement in small and medium quantities involving a certain degree of skilled labour.

Fibre composite specialist Hacotech will present CNC-controlled cutting processes and various finishing possibilities in cooperation with Aristo Graphic Systeme and Lavesan. Alongside cutting, production preparation and customised sizing, the production of dimensionally correct templates and the cutting and custom-sizing of composite materials and prepregs will be on show.

Cutting technology is also centre stage in the special area of Rebstock Consulting, Broetje-Automation and Zünd Systemtechnik, which will be taking part in “Process live” with “Automated Sorting and Kitting”.

Composite producer Saertex and chemical company Scott Bader will demonstrate the RTM process for producing and curing a laminate that complies with the highest fire protection requirements in as little as 1 hour.   

5th International Composites Conference (ICC)
Serial production, stable processes, new markets – the International Composites Conference (ICC) is set to inject a fresh breeze for innovations into the market and to this end brings together processors and users of fibre-reinforced plastics from all over Europe. For the first time, this renowned Conference will be held in parallel with COMPOSITES EUROPE. The lecture programme put together by the trade association Composites Germany and the trade fair will also move closer in terms of content.  

One of tomorrow’s cross-cutting themes keeping the entire industry on its toes are multi-material solutions in nearly all industrial applications. In the construction sector the Conference also deals with the rising use of carbon concrete. Process engineering will focus on processing thermoplastic materials for serial production and stable processes for thermoset plastic processing.  

The partner country of the Conference is the United Kingdom. Especially against the backdrop of the current Brexit debate the ICC aims to foster exchange among all European countries. After all, the UK is among the biggest producers of composites components in Europe.

Themed Tours on Digitalisation, Fibre Glass, Thermoplastics, Automotive and Wind Power
Guided tours and hands-on demonstrations in the exhibition halls complement the conference programme. Themed guided tours revolving around composites application, materials and markets guide trade fair visitors and congress delegates right to the stands of selected exhibitors, who will share with visitors their innovations in the fields of digitalisation of composites production, automotive manufacturing, building and construction, fibreglass, new mobility, thermoplastic materials and wind power.  

New ideas on special areas and joint stands
“Material and Production Technology” is the name of the new special area set up under the guidance of the Institute of Plastics Processing (IKV) of the RWTH Aachen University. In cooperation with other institutes such as the Aachen Center for Integrative Lightweight Production (AZL) the IKV will place manufacturing technology centre stage at the trade fair. In particular, the special area will trace the path from scientific development to practical, industrial implementation.

Tomorrow’s automotive experts will also be given a separate forum: under the heading “Formula Student” students and trainees will present to visitors racing cars and bikes they have engineered.

Lightweight Technologies Forum: platform for multi-material lightweight construction
Lightweight construction remains a driver across the board for many developments in the composites sector. The Lightweight Technologies Forum (LTF) held as part of COMPOSITES EUROPE makes it clear how lightweight construction can be achieved in an economical and resource-efficient manner. This Forum views itself as a cross-industry and multi-material think tank where all parties involved can reflect on these new concepts.

To this end, the Forum in Stuttgart pools lightweight construction projects from automotive manufacturing, aviation and aerospace and mechanical engineering, to name but a few industries that serve as a driving force for many sectors with high demands made on materials, security and reliability.  

This year’s keynote speakers include Airbus Innovation Manager Peter Pirklbauer, lightweight construction expert Prof. Jörg Wellnitz (TU Ingolstadt), Dutch racing driver Jeroen Bleekemolen and lightweight construction, aviation and aerospace specialist Claus Georg Bayreuther (AMC). In their talks they will provide an overview of reference projects and novel manufacturing and joining technologies.  

Combining its own exhibition space with a lecture forum, the LTF demonstrates how glass-fibre reinforced plastics (GRP) and carbon fibre reinforced plastics (CFRP) leverage their strengths mixed with other materials in hybrid structural components. Exhibitors at the Forum and in the neighbouring Lightweight Area include “Leichtbau-Zentrum Sachsen” (Lightweight Construction Center Saxony), Chem-Trend, Gößl + Pfaff, Krempel, Mitsui Chemicals Europe, Leichtbau BW, the VDMA, Gustav Gerster, Potters Ballotini (UK), Yuho (Japan), Riba Composites (Italy) and Stamixco (Switzerland) as well as the journals Lightweight Design (Springer Fachmedien) and Automobil Industrie (Vogel Communications Group), to name but a few.

“Ultralight in Space”: market study on lightweight construction trends in the aerospace industry
The aerospace industry has always served as a pioneer for ultra-lightweight construction pushing many disciplines to their limits as a driver of innovation. The latest technical trends are currently under scrutiny via a market study carried out by consultancy Automotive Management Consulting (AMC) in cooperation with the Luxembourg-based aerospace OEM GRADEL. The results will be presented for the first time at the LTF in Stuttgart on 10 September.  

Presentation of the AVK Innovation Prize
Innovative products and applications in fibre-reinforced plastics, manufacturing processes and the latest insights from research and science, will again be recognised by the German trade association AVK – Industrievereinigung Verstärkte Kunststoffe e. V. with its renowned Innovation Prize. The winners will be announced as part of the trade fair on 10 September and the award-winning products and projects will be on display in a special area.

Presentation of the SMB-BMC Design Award
The European Alliance for SMC BMC will announce the winners of the SMC BMC Design Award 2019 – also on 10 September. The contest already held for the second time now, honours and promotes the design excellence of students or young design professionals who use SMC and BMC components (sheet and bulk moulding compounds) in their designs. This year saw sustainable mobility take centre stage as a theme.

COMPOSITES Night
The event to celebrate the midway point of the trade fair: the COMPOSITES Night at the end of the second trade fair day offers visitors and exhibitors additional opportunities for networking. Participants are in for buffets and live music at the Stage Palladium Theater in Stuttgart.

Matchmaking programme makes trade fair visit more efficient
Thanks to the complimentary networking & meeting platform “matchmaking” visitors and exhibitors can already reach out to contacts in the run-up to COMPOSITES EUROPE. Who is at the trade fair? Who has answers to your specific questions? Who can you team up with to turn new ideas into practice? The matchmaking platform allows you to “filter” and make direct appointments with potential cooperation partners by product category, industry, country, or company.

Career & Composites
With its career&composites stand COMPOSITES EUROPE targets students and graduates who can come here to establish contact with potential employers. On the special area the exhibitors present their companies to interested junior employees and attract attention to vacancies and career opportunities via a Job Wall.

Co-located with Foam Expo Europe
COMPOSITES EUROPE will be co-located with Foam Expo Europe for the first time. This trade fair covers the supply chain of technical foam production and presents moulded, rigid and soft foam solutions – from raw materials to equipment and machinery. The parallel exhibition dates generate special synergies for gaining an overview of lightweight construction materials for such shared applications as the automotive, aviation, construction and sports & leisure industries.